| The SSMicro, SSXYMicro-3A
and SSXYZMicro are a
single/multi axis motion control microstepping boards that is economical and smart. These boards (like all our other motion
control products) comes complete and ready to run. Just connect a PC, Power Supply and
Motor and you are ready to start moving motors! The Simple Step® board has all the features found in today's very expensive
stepper controllers. Some of the features are as follows :
SSXYMicro-3A:
- RoHS compliant.
- 58 MHz Microprocessor Controller.
- Limit Switch Input (per axis).
- Optical Motor Home input (per axis).
- User programmable advanced acceleration and deceleration settings based on User
Programmable Start Velocity, End Velocity and Slope. (per axis)
- User Programmable Full, 1/2, 1/4, 1/8, 1/16 and 1/32 step control (per
axis).
- One (1) Bipolar Stepper motor drive (per axis).
- Single 15.0 - 50.0VDC operation.
- Up to 1.5 amp/phase, switching mode current controlled motor phase outputs (Software adjusted per axis).
- User Programmable Baud Rates (9600, 19.2K, 38.4K, 57.6K (default), 115.2K,
230.4K and 460.8K).
- Multiple
boards on a single serial port and the ability
to intermix Simple Step board types on the network
- Software network address switch select on every
board.
- Simple Step®
Network RS232 and RS422/RS485 communications
(jumper selectable).
- RS422/485 120 ohm balance resistors on board (jumper selectable).
- Option Connector for later add-on or custom boards.
- Two (2) User Controlled Open Collector Output Lines (2-500ma Sink)
(per axis).
- Three (3) User Input Lines (per axis).
- Software Programmable Home Sensor Check
(per axis).
- Diode protected Home and Limit Sensor.
- On Board 5 volt Switcher and Power LED.
- Dual Axis Board Size 5.3" x 4.2" x 0.6"
- Large Dynamic Velocity range (from
1 step per second to 20,000 steps per second) per motor.
- Prescaler installed on all units.
- Software Programmable Motor Power Settings (256 power levels!)
(per axis)
- Synchronous Motor Movements with ALL SSCB , SSCBHC,
SSMicro, SSXYQE, SSXYMicro,
SSXYZMicro and SSXYZ Boards
on the network (Up to 40 motors on 1 serial line)!
- Up to +/- 2,147,483,647 steps of motion.
- EMI (radiated) filtering on all boards to allow
FCC and CE approvals.
- Simple ASCII command set allowing use of standard PC communications packages.
- Decimal or Hexadecimal ASCII numeric values can
be used (per axis).
- 8000 Character IEEPROM program buffer (per axis).
- Jog control for each axis (per axis).
- Single-ended Quadrature Encoder interface (per axis)
- SSWin Program FREE with each purchase. (Windows
95/98/NT/2000/XP)
SSXYMicro-3A board RS232 and RS422/485
problem - Simple Step has
recently found that users who use the SSXYMicro-3A board in RS232 are not
removing the RS422/485 balance resistor shunts on J19 before powering up
the board. User who use RS232 MUST remove the balance resistor shunts or
else there will be a high probability that the RS422/485 IC will blow
which will shut the board down. All current units that are using RS232
that have not had the shunts removed should do so immediately.
SSMicro and SSXYZMicro:
- 30 MHz Microprocessor Controller.
- Limit Switch Input (per axis).
- Optical Motor Home input (per axis).
- User programmable advanced acceleration and deceleration settings based on User
Programmable Start Velocity, End Velocity and Slope. (per axis)
- User Programmable Full, 1/2, 1/4, 1/8, and 1/16 step control (per
axis).
- One (1) Bipolar Stepper motor drive (per axis).
- Single 7.5 - 49VDC operation.
- Up to 1.5 amp/phase, switching mode current controlled motor phase outputs (Software adjusted per axis).
- User Programmable Baud Rates (9600, 19.2K, 38.4K, 57.6K (default), 115.2K).
- Multiple
boards on a single serial port and the ability
to intermix Simple Step board types on the network
- On Board network address switch select on every
board.
- Choice of the Simple Step®
Network RS232 or RS422/RS485 communications.
- Option Connector for later add-on or custom boards.
- Two (2) User Controlled Open Collector Output Lines (2-500ma Sink)
(per axis).
- Three (3) User Input Lines (per axis).
- Software Programmable Home Sensor Check
(per axis).
- Diode protected Home Sensor.
- On Board 5 volt Switcher and Power LED.
- Triple Axis Board Size 7.7" x 4.2" x 0.6"
- Single Axis Board Size 3.77" x 4.2" x
0.6"
- Large Dynamic Velocity range (from
1 step per second to 20,000 steps per second) per motor.
- Prescaler installed on all units.
- Software Programmable Motor Power Settings (256 power levels!)
(per axis)
- Synchronous Motor Movements with ALL SSCB , SSCBHC,
SSMicro, SSXYQE, SSXYMicro,
SSXYZMicro and SSXYZ Boards
on the network (Up to 40 motors on 1 serial line)!
- Up to 65534 steps of motion (27.30625 feet with a user
mechanical resolution of 0.005 inches per step).
- EMI (radiated) filtering on all boards to allow
FCC and CE approvals.
- Simple ASCII command set allowing use of standard PC communications packages.
- Decimal or Hexadecimal ASCII numeric values can
be used (per axis).
- 400 Character IEEPROM buffer for all non-EEPROM
versions (per axis).
- Jog control for each axis (per axis).
- SSWin Program FREE with each purchase. (Windows
95/98/NT/2000/XP)
- Optional Internal 2K,
4K, 8K and 16K of User Programmable on board EEPROM
(Flash) (per axis).
- Programming language for EEPROM with decision branches based on
User Input States (used with
above Option).
- Optional 32
bit movement (2,147,483,647
steps).
- Optional
RTOS (Real-Time Operating System).
Prices does not include tax (if applicable), shipping and
handling. All options (32, IEEPROM, RTOS) are now based
on a flat rate system for all XA Products.
Educational :
Automatic 5% off on all prices
listed above.
| Qty |
Standard Unit
SSMicro |
32
bit |
2K |
4K |
8K |
16K |
RTOS |
| 1 - 9 |
$215.00 (US) |
+$5.00 |
+$4.50 |
+$6.50 |
+$7.00 |
+$8.00 |
+$12.00 |
| 10 - 24 |
$211.00 |
+$4.50 |
+$4.00 |
+$5.80 |
+$6.75 |
+$7.75 |
+$11.50 |
| 25 - 49 |
$205.00 |
+$4.00 |
+$3.50 |
+$5.20 |
+$6.25 |
+$7.25 |
+$11.00 |
| 50-99 |
$196.00 |
+$3.50 |
+$3.00 |
+$4.90 |
+$5.75 |
+$6.75 |
+$10.50 |
Click here to Download AutoCAD R13
drawing of the SSMicro PCB outline
 Click here to download the
SSMicro
Specification sheet in Adobe Version 3.0 PDF
| Qty |
Standard Unit
SSXYMicro-3A |
32
bit |
8K |
RTOS |
| 1 - 9 |
$367.00 (US) |
STANDARD |
STANDARD |
STANDARD |
| 10 - 24 |
$359.00 |
STANDARD |
STANDARD |
STANDARD |
| 25 - 49 |
$352.00 |
STANDARD |
STANDARD |
STANDARD |
| 50-99 |
$334.00 |
STANDARD |
STANDARD |
STANDARD |
Click here to Download AutoCAD R13
drawing of the SSXYMicro PCB outline
Click here to download the SSXYMicro
Specification sheet in Adobe Version 3.0 PDF
| Qty |
Standard Unit
SSXYZMicro |
32
bit |
2K |
4K |
8K |
16K |
RTOS |
| 1 - 9 |
$432.00 (US) |
+$5.00 |
+$4.50 |
+$6.50 |
+$7.00 |
+$8.00 |
+$12.00 |
| 10 - 24 |
$424.00 |
+$4.50 |
+$4.00 |
+$5.80 |
+$6.75 |
+$7.75 |
+$11.50 |
| 25 - 49 |
$415.00 |
+$4.00 |
+$3.50 |
+$5.20 |
+$6.25 |
+$7.25 |
+$11.00 |
| 50-99 |
$404.00 |
+$3.50 |
+$3.00 |
+$4.90 |
+$5.75 |
+$6.75 |
+$10.50 |
Click here to Download AutoCAD R13
drawing of the SSXYZMicro PCB outline
Click here to download the SSXYZMicro
Specification sheet in Adobe Version 3.0 PDF
Download
the latest Simple Step Complete Product manual for all our boards including the General
Information Guide in Adobe PDF Version 3.0 Format (1.87M).
Call today for quantity pricing and delivery. Large and small
orders are welcome. Simple Step®
for Windows included with every purchase.
Information :
You can get more information on
pricing,
delivery, and general questions by clicking here. |
